Miracle 511 Impregnator Sealer, 1 pint, is designed for two-in-one sealing and protecting of your medium to dense porous tile and grout. This advanced sealer protects your tile using an invisible moisture- and stain-resistant guard that won't alter the natural stone look of your flooring. It's recommended for concrete, quarry tile, ceramic tile, porcelain tile, marble, granite, travertine, slate, quartz, brick, terrazzo and even grout
. You can use Miracle 511 Sealer on your indoor and outdoor surfaces, including showers, restrooms, patios and driveways, to protect against moisture damage and staining. It features a unique polymerized silicone formula that effectively seals out UV damage, salt ion intrusion and freeze/thaw damage. Miracle 511 is an economical choice, providing up to 20 times the coverage of competitive products.
For Use On:
Concrete, Quarry Tile, Ceramic Tile, Porcelain Tile, Glazed Tile, Marble, Granite, Travertine, Slate, Grout, Quartz, Brick, Terrazzo. Use for indoor and outdoor applications including showers, restrooms, patios, driveways.Directions For Use:
Read entire label as well as technical and safety data sheets, before using. DO NOT DILUTE. Use as is, direct from approved container.
Apply 511 Impregnator to all surfaces prior to grouting. This allows for quick and easy cleanup after grouting. (Grout can stain many surfaces if this procedure is not used prior to the grouting process.) Apply 511 Impregnator using a Mira Brush or a clean towel. Apply enough to wet the surface. Be careful not to saturate the open grout joints. Allow 511 Impregnator to stand for approximately 3 - 5 minutes for maximum penetration. All excess must be removed at this time by buffing surface with a clean dry towel. This is very important on polished, glazed and porcelain surfaces. Allow to cure for 6 - 12 hours before continuing with the grouting procedure.
Once grouted, make sure that all grout residue is removed from the surface with a clean sponge and water. Allow grout to cure per grout manufacturer's specification. If grout clean up is not performed effectively, an additional cleaning may be necessary to remove remaining grout residue or haze. For this procedure use Phosphoric Acid Cleaner, Heavy Duty Acidic Cleaner or Epoxy Grout Film Remover following the instructions carefully. Once the area has completely dried, proceed with the sealing of the grout for water and stain resistance. Apply 511 Impregnator to all grout with a paint brush. Any excess sealer that gets on the surface should be wiped off with a clean towel before it dries. On larger jobs grout can be sealed by retreating the entire area including the tile or stone surface a second time. Be careful not to allow the sealer to puddle or dry on presealed surfaces. Existing Installations:
Existing Installation Surface Preparation:
Surface must be dry and free of contaminants, including previously applied sealers, dirt, lime & hard water deposits, efflorescence, rust & other heavy dirt and grime.
Surface Coating/Wax Removal:
To remove existing coatings and/or waxes, use Mira Strip or Finish Sealer Stripper as directed.
Heavy Duty Cleaning:
To remove lime and hard water deposits, efflorescence, rust, grease and other heavy dirt and grime use Heavy Duty Acidic Cleaner or Phosphoric Acid Cleaner as directed. For a non acid deep clean use Liquid Poultice as directed.
Use Tile & Stone Cleaner, Porcelain & Ceramic Tile Cleaner, Limestone/Travertine Soap, Counter Kleen as directed.
Existing Installation Application Instructions:
Follow the application instructions previously mentioned, except now, seal the grout and tile or stone surfaces at the same time. When treating surfaces together, make sure that the recessed grout is saturated. Residue Removal:
To remove accumulated 511 Impregnator residue, use Miracle Residue Remover as directed. Color and Gloss Enhancement:
For color & gloss enhancement, use Mira Matte or High-Gloss Finish Sealer as directed. Cure Time:
Will be dry to the touch in 1 - 3 hours and may be used for normal foot traffic. For optimum results the area should be kept dry and free from staining materials for 72 hours.
- Coverage ranges from 62.5 to 500 square feet per pint, depending on the type of surface to which it is applied.
- On more porous surfaces use 511 Porous Plus as directed.
- For questions concerning grout, refer to the grout manufacturer's specifications.
- 511 Impregnator will not stop acid etching.
- Due to the differences of each substrate, several inconspicuous test patches should be completed to assure maximum performance. User must determine suitability of the product for their intended use.
- 511 Impregnator has been used successfully for compliance with the American Disability Act's recommendations for slip resistance (ASTM C 1028-89) on polished & honed surfaces.
- Protect neighboring surfaces including wood, carpet, metal, landscaping and other non masonry surfaces.
- ORM-D: FLAMMABLE LIQUID, Class 3, Paint & related products. All safety information for this item is detailed on the product Safety Data Sheet.