Laticrete StoneTech High Gloss Finishing Sealer, 1-Gallon
Product Description
Laticrete (DuPont™) StoneTech® Professional High Gloss Finishing Sealer, 1 Gallon
Two-in-one formula leaves a wet-look finish and protects against stains.
Easy-to-use, water-based formula.
Interior use.
LEED points qualified product.
For Use On: Slate, saltillo, limestone, travertine and concrete floors. Not intended for use on glazed, polished, or non-absorbing surfaces, wood floors & decks, showers, countertops, or near pool areas. Interior use only.
Directions For Use:
Read product label prior to use. Always test in a small inconspicuous area to determine appropriate application method, achievement of desired results, and to ensure good adhesion.
Ensure work area is well-ventilated during application and until surface is dry.
Avoid applying in direct sunlight.
Surface must be thoroughly clean, dry, and free of any sealers or coatings before application.
Application to a dirty or dusty surface will affect adhesion and appearance.
High Gloss Finishing Sealer should not be applied to a wet or moist surface.
Avoid applying onto surfaces not intended for treatment.
For new installations, sealer can be applied as soon as 48-72 hours after grouting.
Fresh concrete slabs require a minimum of 28 days to cure before applying the sealer.
Coverage Gallon: 100-300 sq ft depending on porosity of stone surface.
Expected Wear: 3-5 years however Touch up on higher traffic areas may be required on a more frequent basis.
Safety Data: DuPont™ StoneTech® Professional High Gloss Finishing Sealer MSDS
Additional Information: Clean surface as needed with Revitalizer® Cleaner & Protector or Stone & Tile Cleaner.
For Use On: Slate, saltillo, limestone, travertine and concrete floors. Not intended for use on glazed, polished, or non-absorbing surfaces, wood floors & decks, showers, countertops, or near pool areas. Interior use only.
Directions For Use:
Read product label prior to use. Always test in a small inconspicuous area to determine appropriate application method, achievement of desired results, and to ensure good adhesion.
- Liberally apply 2-4 even coats with a natural bristle brush, roller, or paint pad applicator. Do not apply product with a sprayer or sponge. Avoid puddling of liquid during application. Failure to apply a sufficient amount of sealer to the surface may result in an undesirable finish or degradation of the coating. More coats may be applied if desired.
- Allow 30-45 minutes between coats or until surface is dry to the touch.
- Surface traffic may begin 12 hours after final application; keep installation dry for a minimum of 12 hours; full cure is achieved in 24-48 hours.
- Keep surface clean and dry as finished surfaces may become slippery when wet.
Ensure work area is well-ventilated during application and until surface is dry.
Avoid applying in direct sunlight.
Surface must be thoroughly clean, dry, and free of any sealers or coatings before application.
Application to a dirty or dusty surface will affect adhesion and appearance.
High Gloss Finishing Sealer should not be applied to a wet or moist surface.
Avoid applying onto surfaces not intended for treatment.
For new installations, sealer can be applied as soon as 48-72 hours after grouting.
Fresh concrete slabs require a minimum of 28 days to cure before applying the sealer.
Coverage Gallon: 100-300 sq ft depending on porosity of stone surface.
Expected Wear: 3-5 years however Touch up on higher traffic areas may be required on a more frequent basis.
Safety Data: DuPont™ StoneTech® Professional High Gloss Finishing Sealer MSDS
Additional Information: Clean surface as needed with Revitalizer® Cleaner & Protector or Stone & Tile Cleaner.
Stone, Tile, Grout - Cleaner
$13.95, 2/$25.12
NEW MARKDOWN!
Regular price:$16.15
Sale price:$11.30 Save 30%
NEW MARKDOWN!
Regular price:$44.00
Sale price:$35.00 Save 20%
Stone, Tile, Grout - Cleaner
$19.00, 2/$34.20
