Home > Vinyl Floor Care > HILWAY DIRECT Hard Surface Floor Care > Hilway Direct PLUS Floor Finish & Cleaner/Maintainer, 5 Gal

Hilway Direct PLUS Floor Finish & Cleaner/Maintainer, 5 Gal

Hilway Direct PLUS Floor Finish & Cleaner/Maintainer, 5 Gal
Item Number: HD-PLUS5G
1+ pieces$207.40 ea.
2 + pieces$186.66 ea.
Regular price:$207.40
Quantity:


Hilway Direct PLUS Floor Finish & Cleaner/Maintainer, 5 Gallon

This economical 5-gallon bottle of Hilway Direct PLUS Floor Finish & Cleaner/Maintainer provides an all-in-one finish, clean and maintain on your resilient floors, including vinyl (sheet, VCT, LVT), rubber, linoleum, cork, marble, slate, quarry tile, terrazzo, concrete and asphalt tile. It is a 30 percent high solids cleaner that may be used as a floor finish only or as a one-step cleaner for cleaning and maintaining. The low-sheen finish leaves behind a hard-wearing, acrylic layer to resist scratches and scuffs. It contains no VOCs and is non-hazardous, so it's well-suited for use in busy, commercial environments. This bottle of Hilway Direct PLUS (5 gal.) from 1877FloorGuy qualifies for volume discounts for even more savings. We're a distributor of Hilway Direct products, so we're happy to answer any and all questions you may have about this cleaner. Coverage for a single coat: 1,500-2,000 square feet per gallon. Proper application requires two (2) coats. Coverage may vary depending on porosity of flooring material.

For Use On: Vinyl (sheet, VCT, LVT), Rubber, Linoleum, Cork, Marble, Slate, Quarry Tile, Terazzo, Concrete, Asphalt Tile

Directions For Use:
Initial Application:
  1. Clean floor thoroughly prior to application of finish. For floors with a factory finish, remove finish following flooring manufacturer’s instructions. Rinse or neutralize after removing old coating.
  2. Shake finish well then let it settle 5 minutes before use.
  3. Apply a thin, even, undiluted coat using a microfiber applicator mop.
  4. Apply 2-3 coats, allowing each coat to air dry completely (approx 30-60 minutes) between coats.
  5. Allow finish to dry for at least eight (8) hours after the second coat and before use.
Daily Cleaning, Mop & Bucket:
  1. Sweep floor to remove loose dirt.
  2. Dilute 1oz Hilway Direct Plus per 1 gallon warm water.
  3. Mop floor with diluted cleaning solution using a 2-bucket system. Use clean water in 2nd bucket to rinse mop.
  4. Pick up excess solution with a tightly wrung-out mop.
  5. Allow floor to air dry. Do not rinse floor after cleaning.
Daily Cleaning, Auto Scrubbing Machine:
  1. Sweep floor to remove loose dirt.
  2. Dilute 1oz Hilway Direct Plus per 1 gallon warm water.
  3. Scrub floor with diluted cleaning solution.
  4. Trail mop excessive wet areas behind scrubber.
  5. Allow floor to air dry. Do not rinse floor after cleaning.
Notes:
  • Do not use a treated mop for application.
  • When applying the product avoid strong sunlight and drafts.
  • Turn off under floor heat before commencing work.
  • Ensure sufficient ventilation.
  • Read complete product label and manufacturer instructions prior to application.

  • Coverage: Single Coat: 1500-2000 square feet per gallon. Proper application requires two (2) coats. Coverage may vary depending on porosity of flooring material.

    Safety Data: Hilway Direct Plus Floor Finish & Cleaner/Maintainer MSDS

    Manufacturer Part Number: HD-PLUS5G
    Brand: Hilway Direct


    Frequently Purchased With:



    Customer Testimonial:
    Read more...
    ecommerce provided by Yahoo! Small Business

    Hilway Direct PLUS Floor Finish & Cleaner/Maintainer, 5 Gal