| || |
Miracle 511 Porous Plus Sealer, 8oz Spray
Miracle 511 Porous Plus Sealer, 8 oz Spray
Protects the most porous tile, stone and grout surfaces. Provides water-resistance, stain-resistance and slip-resistance. Low Toxicity, non-yellowing, UV transparent. Forms an invisible barrier that will not alter the look of the surface to which it is applied. Interior and exterior applications. 511 Porous Plus averages 2 to 10 times the coverage of competitive products. Out performs competitive products. Can be used on freshly poured concrete to retard the evaporation of water.
For Use On: Grout, Flamed, Honed & Polished Limestone, Flamed, Honed & Polished Granite, Flamed, Honed & Polished Marble, Saltillo Tile, Terra Cotta Pavers, Masonry, Sandstone, Porous Slate & Brick, Cement, Concrete, Cantera/Adoquin, Flagstone, Sanded Grout, Stucco. Use for indoor and outdoor applications including showers, restrooms, garages, pool areas.
Directions For Use:
Read entire label and PDS/MSDS before using. 511 Porous Plus should not be diluted or thinned in any way. Use as is direct from approved container.
Sealing As a Grout Release: Apply 511 Porous Plus to all surfaces prior to grouting. This step will allow quick and easy cleanup after grouting. Grout can stain many surfaces if this procedure is not used prior to the grouting process. Apply 511 Porous Plus using a Mira Brush or a clean towel. Apply enough to wet the surface. Be careful not to saturate the open grout joints. Allow 511 Porous Plus to stand for approximately 3 - 5 minutes for maximum penetration. Any excess sealer remaining at this time should be removed by wiping the surface with a clean dry towel. On very porous surfaces apply another application after the previous application has dried 2-3 hours. Any excess sealer that has dried on the surface creating a residue/film, may be removed by applying Residue Remover. Apply Residue Remover undiluted to the affected area with a clean dry towel. Let it sit for 1 - 2 minutes before buffing the area with a second clean dry towel. Allow to cure for 6 - 12 hours before continuing with the grouting procedure per manufacturers specification.
After Grouting: Once grouted, make sure that all grout residue is removed from the surface with a clean sponge and water. Allow grout to dry at least 24 - 72 hours. If grout clean up is not performed effectively, an additional cleaning may be necessary to remove remaining grout residue or haze. For this procedure use Phosphoric Acid Cleaner, Heavy Duty Acidic Cleaner, or Epoxy Grout Film Remover following the instructions carefully.
Grout Sealing: Once the area has completely dried, proceed with the sealing of the grout for water and stain resistance. Apply 511 Porous Plus to all grout with a paint brush. Any excess sealer that gets on the surface should be wiped off with a clean towel before it dries. On larger jobs grout can be sealed by retreating the entire area including the tile or stone surface a second time. Be careful not to allow the sealer to puddle or dry on presealed surfaces.
Residue Removal: To remove accumulated 511 Porous Plus residue, use Miracle Residue Remover as directed.
Surface Preparation: Surface must be dry and free of contaminants, including previously applied sealers, dirt, lime & hard water deposits, efflorescence, rust & other heavy dirt and grime.
Floor Coating/Wax Removal: To remove existing coatings and/or waxes, use Mira Strip or Finish Sealer Stripper following the instructions carefully.
Heavy Duty Cleaning: To remove lime and hard water deposits, efflorescence, rust, grease and other heavy dirt and grime use Heavy Duty Acidic Cleaner or Phosphoric Acid Cleaner as directed. For a non-acid deep clean use Liquid Poultice as directed. All strippers and/or cleaners should be thoroughly rinsed with clean water and the surface allowed to dry.
Sealing Existing Surfaces: Follow the application instructions previously mentioned, except now, seal the grout and tile or stone surfaces at the same time. When treating surfaces together, make sure that the recessed grout is saturated.
Light Cleaning: Use Tile & Stone Cleaner, Porcelain & Ceramic Tile Cleaner, Limestone/Travertine Soap & Counter Kleen as directed.
Cure Time: Will be dry to the touch in 1 - 3 hours and may be used for normal foot traffic. For optimum results the area should be kept dry and free from staining materials for 24 - 72 hours.
Coverage: Coverage ranges from 32 - 125 square feet per 8 ounces depending on the type of surface to which it is applied. Reference coverage chart on the Information Sheet pdf file for a more detailed coverage chart.
Safety Data: Miracle511PorousPlusMSDS
UPC #: 753927512551
Manufacturer Part Number: LA PLU 8OZ B 12
Brand: Miracle Sealants
Frequently Purchased With:
Copyright 2000-2014 1877FloorGuy.com All rights reserved.
Miracle 511 Porous Plus Sealer, 8oz Spray