Home > Vinyl Floor Care > SPARTAN Commercial Floor Care > Spartan N/C No Charge Dissipative Floor Finish > Spartan NO CHARGE STATIC DISSIPATIVE FLOOR FINISH 401304, 1 Gallon

Spartan NO CHARGE STATIC DISSIPATIVE FLOOR FINISH 401304, 1 Gallon

Spartan NO CHARGE STATIC DISSIPATIVE FLOOR FINISH 401304, 1 Gallon
Item Number: SPAR-401304
1 - 3 pieces$55.85 ea.
4 + pieces$50.27 ea.
Regular price:$55.85
Quantity:


Spartan N/C No ChargeŽ Static Dissipative Floor Finish, 1 Gallon

Safely clean floors while controlling static electricity with Spartan No Charge Static Dissipative Floor Finish (1-gallon). This commercial-use floor cleaning product is formulated for specific flooring types - such as ESD floors - in protected environments that have a high degree of static electricity, like IT rooms with computer servers or in rooms with raised flooring with electrical cords below. It contains Spartan's proprietary thermoplastic polymers, resins and waxes that reduce static electricity on the floor.

Unlike traditional finish products, Spartan No Charge Finish is not intended to add gloss or beauty, but to instead to reduce the resistivity of the floor. Check into your information technology room requirements to see if this product is suitable for your use. Facilities that use this finish should take regular readings for resistivity requirements to ensure the floor stays within required specification for resistivity. If the facility does not have a specification or does not take regular floor readings, it is likely that antistatic finish is not required. Always test a small, inconspicuous area of floor prior to full use.

Use this high-quality static dissipative floor finish on floors with a specialized finish, specifically for use on conductive floor tiles in facilities that require resistivity levels below the level obtainable with traditional finish.

Coverage: 2,000 to 3,000 square feet per gallon depending on application method and porosity of floor.
  • Exceeds Mil Spec static decay time standards of less than 2 seconds
  • Meets ASTM Standard in both low and high humidity environments
  • UL approved for slip-resistance that meets or exceeds 0.5 static coefficient of friction as determined by UL testing, ASTM Method D 2047
  • Also available in an economical 5-gallon size
For Use On: Specialized finish specifically for use on conductive floor tiles in facilities that require resistivity levels below the level obtainable with traditional finish. Always test a small, inconspicuous area of floor prior to full use.

Directions For Use:
Prior to use, read product label and SDS for safety precautions and proper application. 
Initial Application: Strip all old wax or floor finish completely from floor. Apply two to three uniform coats of floor finish. Allow each coat of finish to dry a minimum of forty-five minutes before applying the next coat. High humidity and/or cold temperatures will greatly extend dry times. Note: It is imperative to allow each coat of finish to dry before applying the next.

Only apply 2 or 3 coats. Less than two coats or more than three coats will result in resistivity outside the limits traditionally specified. More finish is not better. Allow significant dry time between coats. Facilities that require N/C Finish will have extremely tight temperature and humidity controls. Usually, temperature is low and humidity is high, which causes extended dry times. Do not over apply and do not rush coats. Application rates of 2000- 3000 sq. ft./gal are mandatory. Dry time between coats can last well over an hour, depending on the specific conditions of the room.

Maintenance: Dust floors regularly. If wet cleaning is necessary, always use N/C No Charge Static Dissipative Floor Cleaner. Do not over wet the floor. Lightly damp mop or spray and mop clean. Deep scrub and re-coat, or completely strip and reapply N/C No Charge Static Dissipative Finish, as needed.

Do not use excessive water. The antistatic agent in No Charge floor finish is extremely hydrophilic ("water loving") and will quickly leach from the floor when exposed to moisture. The floor will take on a whitened, blotchy or streaked appearance if overexposed to liquid. Most ESD sensitive facilities are clean room environments that should require very little wet cleaning. Overexposure to water will cause resistivity readings to drop out of specification and finish recoating is the only solution to restore the integrity of the floor's finish.

Do not auto scrub, burnish or buff. Do not use any cleaners other than N/C No Charge Static Dissipative Floor Cleaner.

Spartan No Charge Floor Finish Safety Data Sheet

Spartan No Charge Finish Product Data Information

Specifically recommended for use on the following floor brands: 
(Check compatibility with specific flooring material prior to use.)
Johnsonite (Tarkett Commercial Flooring)

Manufacturer Part Number: 4013-04
Brand: Spartan


Frequently Purchased With:



Customer Testimonial:
Read more...
ecommerce provided by Yahoo! Small Business

Spartan NO CHARGE STATIC DISSIPATIVE FLOOR FINISH 401304, 1 Gallon